Burdekin Motorcycles

Provides spare prop installation components for the models listed. (For other models, order parts individually from the standard parts list.)

Provides spare prop installation components for the models listed. (For other models, order parts individually from the standard parts list.)

Provides spare prop installation components for the models listed. (For other models, order parts individually from the standard parts list.)

Provides spare prop installation components for the models listed. (For other models, order parts individually from the standard parts list.)

DESIGNED FOR 4 STROKE OUTBOARDS AND INBOARD BOAT ENGINES.              

• EVERY 100 HOURS OF RUNNING "CHANGE ENGINE & GEAR NOW"  WILL FLASH.      
• EVERY 100 HOURS THE METER WILL FLASH "CHANGE SPARK PLUGS NOW".         
  

  * AT 500 HOURS OPERATION THE METER WILL FLASH "VALVE SERVICE NOW".       

• ALL FUNCTIONS COUNT DOWN SHOWING YOU BALANCE OF TIME BEFORE SERVICE.   
• EACH FUNCTION IS RE-SETTABLE BY HOLDING DOWN THE BUTTON WHEN THE SERVICE FUNCTION THAT IS DUE IS FLASHING.                              
• THIS METRE ALSO INCLUDES A "INDIVIDUAL RUNNING TIMER" MODE TO TRACK RUNNING SESSIONS. IT CAN BE ERASED WITH RESET BUTTON.                  

• OPERATES WITH NEW GENERATION 4 STROKE "PEN STICK" COILS, OR EARLIER GENERATION IGNITIONS.
  

  * PICK-UP WIRE LENGTH CAN BE TRIMMED.              
                                             

This high-volume (290 liters/minute) 12 volt portable air pump inflates and deflates towables, boats, pools, mattresses and beach toys quickly and effectively. Most pumps on the market don’t put out this kind of air pressure and volume (9.6 cu.ft./min., .8 psi). The universal valve fittings fit all popular valves. For added convenience, the cigarette lighter/12 volt power port plug is equipped with a 10’ long power cord.

These contour fenders stay put and stow conveniently under boat seats. They hinge to wrap around the gunwale and hull, following the contours of the boat. Constructed of a durable marine-grade, tri-laminate cover, with closed cell foam inside. There’s a tough polycarbonate grommet at each end for hanging from cleats. 24" long x 6" wide x 2-1/2" thick

These contour fenders stay put and stow conveniently under boat seats. They hinge to wrap around the gunwale and hull, following the contours of the boat. Constructed of a durable marine-grade, tri-laminate cover, with closed cell foam inside. There’s a tough polycarbonate grommet at each end for hanging from cleats. 24" (60cm) long x 6" (15cm) wide x 2-1/2" (6cm) thick.

The Yamaha Trailering Tilt Motor Support has been designed to allow highway transport of your boat with the motor in a tilted position. The trailering support prevents the motor from returning to the vertical position and possible contact with the road surface. The Motor Support also prevents excessive loads, created by road surface conditions and from damaging the tilt assembly.

Note:
The Yamaha Trailering Motor Support can be cut to size, if your outboard sits too high or you have problems with tilting your motor high enough to install this support. Simply cut the Motor Support to the appropriate length using a mitre or hacksaw.

Fitment:
For both two and four stroke models, 8 – 115HP with a single ram power tilt assembly only.
Will also fit: F115B, F130 and VF115.
 

The Yamaha Trailering Tilt Motor Support has been designed to allow highway transport of your boat with the motor in a tilted position. The trailering support prevents the motor from returning to the vertical position and possible contact with the road surface. The Motor Support also prevents excessive loads, created by road surface conditions and from damaging the tilt assembly.

Note:
After installing the outboard trailering support(s), the outboard is tilted down until the trim rods start to retract. The Yamaha Outboard Trailering Supports can be customized for applications with restricted full tilt up angles due to interference with the boat or other components. A maximum of 1-_" may be removed from the overall length to permit installation of the trailering supports. Cut lines, in _" increments, are located on the trailering support for ease of cutting. When reducing the overall length, cut or grind off material to duplicate the original end taper, on the cut end, to allow proper function of the outboard trailering supports. Failure to taper the cut end will cause damage to the support and prevent proper support of the outboard.

Fitment:
Use one support for F115 – F250 four stroke and all 60 – 300HP two stroke models while trailering.
Will not fit: F115B, F130 and VF115 (see part number MAR-MTSPT-WD for these)

For F300 – F350 models require two supports.

They are quickly installed over the port trim rod on F115 – F250 four stroke and all 60 – 300HP two stroke models or both trim rods on the F300 – F350 V8 models.

Trailering supports must be used on twin ram motors.

Vinyl Repair Kit